Skip to content
Printer care

Keep it printing.

Most failed prints aren't bad models: they're a dirty plate, a worn nozzle or a dry rail. Here's a routine that works for any printer, and every maker's official maintenance guide in one place.

Keep a logbook for your own printers and VERTEX tells you when each job is due.

The routine

Times are a guide for a printer that runs most days. Always follow your maker's schedule where it differs: their guides are linked below.

WhenWhat
Every printPlate clean and free of fingerprints · nozzle tip clear of old plastic · filament path free of tangles · watch the first layer
Every weekWash the plate (see below) · brush the hotend and nozzle while warm · clear the purge chute and waste bin · check the part-cooling fan spins freely
Every monthClean and lubricate rods, rails and leadscrews the way your maker says · check belt tension · clean extruder gears · tighten frame screws · update firmware
Every 3 monthsReplace carbon or HEPA filters (daily use) · check the PTFE tube ends for wear · inspect wiring at the toolhead and bed for rubbing · deep-clean the multi-material unit
Every 6–12 monthsReplace brass nozzles (sooner with abrasive filament) · check bearings, wheels and belts for wear · re-run the calibrations (bed mesh, flow, input shaping)

Build plate

  • Wash, don't wipe. Warm water and a drop of dish soap, rinsed and dried with a clean towel, removes the skin oil that alcohol only spreads around. Use isopropyl alcohol (IPA) between washes.
  • Textured PEI likes a wash. Smooth PEI with PETG needs a release layer (glue stick) or it can tear the surface.
  • Hold the plate by its edges. A fingerprint is the most common cause of a corner lifting.

Nozzle and hotend

  • Brush the nozzle while it's warm with a brass brush, never steel on a coated nozzle.
  • Clogs: try a cold pull (heat, push a bit of nylon or PLA through, cool to about 90 °C for PLA, pull firmly) before taking anything apart.
  • Carbon fibre, glass fibre, glow-in-the-dark and wood filaments wear brass nozzles fast. Use hardened steel or a ruby-tipped nozzle for them.
  • Tighten hotends to your maker's torque only when hot, if their guide says so. Many modern hotends are swapped whole instead.

Extruder

  • Dust and plastic shavings collect in the drive gears: brush them out and check the tension (too tight crushes filament, too loose clicks and skips).
  • Clicking or grinding usually means a partial clog, a temperature that's too low, or wet filament. It's rarely the extruder itself.

Rails, rods and belts

  • Use what your maker says, where they say. Linear rails, smooth rods and carbon rods each need something different, and some (carbon rods) must stay dry. Too much grease attracts dust.
  • Belts should sound like a low note when plucked, both sides alike on CoreXY. Uneven belts show as ringing and skew.
  • V-wheel printers: a wheel should just stop turning when you pinch it. Flat spots mean time for new wheels.

Z axis

  • Clean the leadscrews and add a thin film of the grease your maker specifies. Banding at regular heights often starts here.
  • Check the bed's mounting or levelling springs haven't loosened, and re-run the bed mesh after moving the printer.

Filament and drying

  • Nylon, TPU, PETG, PC and PVA pick up water from the air within days: stringing, popping and rough walls are the signs. Dry them, store them sealed with desiccant, and print from a dry box if you can.
  • Keep spools out of the sun and away from dust. Cut the filament end at an angle before loading it.

Electronics and firmware

  • Update firmware from the maker's own site or app, with the printer idle.
  • Look for rubbed or kinked wires where they move (toolhead, heated bed). Loose connectors cause heater and thermistor errors.
  • Keep fans and vents clear of dust. Hot electronics fail early.

Enclosure and air

  • ABS, ASA, PC and nylon give off fumes and fine particles: print them enclosed and vented or filtered, in a room with fresh air.
  • Replace carbon and HEPA filters on schedule (about every three months of daily use is common).

AMS, CFS and other multi-material units

  • Keep the desiccant fresh and the lid shut: these units store your filament as well as feed it.
  • Clean the feeders and hubs of shavings, and use spools in good condition (cardboard spools often need an adapter or a printed rim).
  • A snapped piece of filament in the path is the most common jam: follow the maker's guide to clear it rather than forcing it.

Laser modules

  • Brush dust off the module after every job. When the printer asks, remove the air nozzle and wipe the lens: a dirty lens loses power and can overheat.
  • Never cut PVC or vinyl (they release chlorine gas). Clear and blue acrylic pass straight through blue diode lasers (like 455 nm modules): use a colour the laser can absorb.
  • Never leave a laser job running unattended, and keep the enclosure and exhaust working.

Guides by brand

Straight from each maker. Pick your printer on its own page to see its bed size and its guide together.

Missing yours? Tell us in the forum and we'll add it. Stuck on something? Ask in Printing help: someone has seen it before.